Water Heater Repair Arlington TX's Blog

Arlington Homeowner advice and maintenance tips for water heaters.

Water Heater T&P Valve Test

The Causes of a Water Heater Tank Explosion

With regards to having to undertake servicing on ones water heater, it is a comparatively minimal maintenance appliance. However, one critical aspect of it should be checked out routinely. Hot Water Heater Repair Arlington TX would like to pass on this safety information concerning ones water heater today.

High temperature if merged with tank corrosion inside the storage tank may cause an explosion. Whenever the water temperature is below 212 degrees Fahrenheit, one shall be safe from an explosion, though there is a threat of scalding at that temperature. However, if the water temperature is over 212 degrees, water transforms into steam, which will expand to 1,700 times the space it occupies as water. This is when an explosion can happen.

Warning Indicators of a Water Heater Explosion

The leading sign is if one goes to get hot water from a faucet and only steam comes out. Promptly turn off electric power if one has an electric water heater. If one owns a gas hot water heater, turn off the gas valve going to the water heater. And then, give us a call to come assess the situation.

Minimizing Potential Water Heater Dangers

The most crucial routine maintenance activity with a water heater is to examine the pressure relief valve, also referred to as the T&P valve, on a usual basis. This valve helps regulate the pressure accumulation within the water storage tank to avert a threatening increase in temperature and overpressure.

Warning!

Be careful, the water discharge out of a T&P valve might be really hot. If you do not feel at ease examining the valve let us know. In addition, doing any type of fixes to the valve ought to be performed by a expert plumbing repair business.

How to Test the T&P Valve

Remove anything from around the area around the overflow pipe and floor drain.

Raise the test handle for roughly 5 seconds or until the water runs clear.

Release the handle.

If the T&P valve continues to run with water, raise the handle up and down rapidly to have it reseat itself. One might have to do this a handful of times. IF it has not been tested for a while, it might be difficult to raise it at first. Avoid using an excessive amount of force, however could need to utilize a little.

If the T&P valve continues to have water coming out, it should be changed.

Some other things to watch out for are rust on the stem of the valve. If there is any water leaking out of the valve stem or from the drain valve.

Seeking far more hints? Have a look at our other articles here:

Water Heater Maintenance Infographic

Arlington TX Water Heater Maintenance

Related T&P Valve Testing Videos

Mythbusters did a test of the potential dangers of hot water heater explosions here:

Water Heater T&P Valve Repair Arlington TX

What the Experts Say

  • The discharge from a T&P valve can be very hot. It is very important that all T&P valves be installed properly with a discharge line piped downward to an adequate drain to avoid property damage and to minimize possible human contact.
    Read more…

Watts Water Technologies

If the temperature in your heater remains high after you turn down the thermostat, the thermostat may be faulty. Consult a professional for repair. Read more…

Home Guides

Pressure relief valves sometime develop a drip when opened for the first time in years. Try opening and closing it a few times to see if it will seat itself. If you have a large leak or the drip doesn’t stop on its own in a day or two, the valve will need to be replaced.  Read more…

Today's Homeowner

Check out some of our other water heater tips in our blog

Eliminating Water Heater Odors in Your Arlington Home

Arlington Water Heater Odor Repair

Are you experiencing a problem with foul odors coming from the water originating from your water heater? It happens at times for a few various reasons. Here is what Water Heater Repair Arlington TX suggests to do to make sure your water smells better and to remove any terrible tastes quickly.

Causes for Arlington Water Heater Smells?

Bacteria getting into the water system is the most common reason ones water in your own home will have smells. If you home makes use of well water or cities that make use of wells for the water source, increases the likelihood of this developing.

With a water heater temperature setting of 140 degrees or above will assist in lowering the development of microorganisms inside the water storage tank.

The Best Ways to Remove Smelly Water Smells

The following instructions discuss how you can use chlorine bleach to cleanse a water heater.

The electric or gas going to the water heater tank needs to first be shut off.

Next, the cold water supply off that goes to the tank needs to be turned off.

Open the hot water faucet of the kitchen area sink to permit air to enter the tank.

With a a yard hose attached to the storage tank drain valve, drain the water inside the water heater.

Then shut the drain valve as soon as it is empty.

The next step is adding the bleach.
If the pipe for the cold water travelling inside the storage tank is a flexible hose, unscrew it from the tank. Otherwise, one will have to take off the pressure relief valve, which is more involved. For electric water heaters, one of the elements can be removed.

Utilize a funnel to pour bleach into the opening.
Add 5 ounces of bleach per gallon of the tank ability.
So if you have a 50 gallon water heater, you will need 250 ounces of bleach, or close to 2 gallons.

Reinstall the water line or pressure relief valve.

Fill the tank back up with water again.

Close the hot water faucet of the kitchen area faucet as quickly as all the air runs out the line.

Run all the hot water appliances until the smell of bleach is apparent. We want to get rid of the germs that can be found in the water lines also, not only inside of the water heater.

Allow the water to remain in the tank and water lines without using and hot water for 2 to 3 hours.

Empty the storage tank again and refill it. This time let it stay for at least thirty minutes and just as before drain it.

Fill the tank back up. Open all the hot water fixtures and let them run up until the odor of bleach is gone.

For gas water heaters, relight the water heater pilot light. For electric water heaters, turn the power on again.

In addition, by replacing the anode rods, or even the type utilized can work as the next video shows:

Additionally, by replacing the anode rods, or perhaps the type employed can work as the next video shows:

Odors from Arlington Water Heater

What the Experts Say

According to Soquel Creek Water District, “The smell is the result of four factors that must all be present for the odor to develop. These factors include:

  • A high concentration of sulfate in the raw water
  • Sulfate reducing bacteria, non-toxic to humans (sulfate is reduced to a sulfide state by the bacteria)
  • Little or no dissolved oxygen in the water
  • Hydrogen (a component of water which may be present due to water conditions reacting with the anode)”  Read more here…

Soquel Creek Water District

How is hydrogen sulfide gas produced in a water heater?

A water heater can provide an ideal environment for the conversion of sulfate to hydrogen sulfide gas. The water heater can produce hydrogen sulfide gas in two ways – creating a warm environment where sulfur bacteria can live, and sustaining a reaction between sulfate in the water and the water heater anode.  Read more…

Minnesota Department of Health

Check out some of our other water heater tips in our blog

Best Water Heater Temperature Level

An element about ones water heater of which many Arlington homeowners has likely definitely not considered a lot concerning is the temperature setting. What is the perfect temperature level for the hot water in ones family home? In this post Water Heater Repair Arlington TX will explore the positives and negatives of varied levels for house owners to decide on exactly what will work most effectively for them and their family, for there are certain health disadvantages that ought to be taken into consideration.

A good number of water heater producers preset the temperature of their hot water heaters to 140 degrees. If you have gotten the heater in your property installed or changed while being there, this might be precisely what it is already set at if you haven’t adjusted it. It can also be tough to recognise precisely what the authentic temperature is on quite a few water heater brands for the dial is named as warm, hot, really hot. We are convinced it seems to be a excellent promoting characteristic to market water heaters that have the ability to heat water to 1000 degrees, nonetheless we will find that it is highly excessive.

In cases where the temperature dial has no degrees written upon it, fill up a glass of hot water from a faucet and put a cooking thermometer inside it to see the temperature level.

Energy Saving Costs With Arlington Water Heater Temperature Settings

It happens to be presumed that through shifting the setting from 140 to 120 degrees can save between six to ten % of the energy made use of from the water heater. In money, this would allow $6 to $20 yearly in cost savings. The U.S. Department of Energy expresses a temperature setting of 120 is the ideal strategy to cut back on home energy costs.

If in conclusion of the article one thinks an even lower temperature setting is secure for ones residence, subsequently the financial savings may well be more than suggested earlier.

Potential Health Risks With Water Heater Temperature Settings

As the infographic beneath illustrates, there are health disadvantages if the hot water temperature is too cool. Legionella bacteria is the possible unhealthy variable to consider. It could possibly grow in the temperature spectrum of 68 to 122 degrees. Consequently, if ones water heater is placed less than 122 degrees, there does exist the likelihood it could grow on the inside of ones hot water heater storage tank.

How is Legionella bacteria harmful? A variety of pneumonia could be transferred if someone breathes water that Legionella bacteria has contaminated. This would typically take place when inhaling water moisture by a shower. Consuming the water is in most cases acceptable.

Approximately 8,000 to 18,000 Americans catch this each year states the Centers for Disease Control and Prevention, and 5 to 30 % of such incidents result in death. This is not stated to distress anyone, but just as a practical idea for people that could possibly be even more susceptible to acquiring Legionella Disease.

According to OSHA, “At low levels of contamination, the chance of getting Legionnaires’ disease from a water source is very slight. The problem arises when high concentrations of the organism grow in water systems. Water heaters, cooling towers, and warm, stagnant water can provide ideal conditions for the growth of the organism.”  (read more)Arlington Water Heater Repair

Arguments to Decrease Water Heater Temperatures

One of many motives to never have ones water heater established at approximately 140 degrees is the hazard of getting scalded or burned by the water. For Arlington property owners that have kids or older adults, this ought to be taken into account. The Consumer Product Safety Commission (CPSC) proposes a setting of 120 because of motives. One can find currently bath faucet slip covers that have a LED temperature reading that can be practical also!

When decreasing the temperature setting, take a look at the dishwasher manual to determine what the the bare minimum water temperature level is for it. A few brands require it to be particularly high.

Sometimes it is a tricky issue to make a decision on Hot Water Heater Repair Arlington TX appreciates. We trust the material in this article and the infographic underneath will help inform our Arlington neighbors and clients on the preferred water heater temperature issue.

Hot Water Heater Repair Arlington TX

Total Water Heater Maintenance Tasks

Water Heater Repair Arlington TX is not about to discuss the unlucky reports concerning water heater maintenance of “getting up to the freezing bath,” here. In addition, we shall presume that one knows the straightforward notion of ensuring ones water heater is maintained routinely in an effort to receive the most from its expected life. This can help one reduce costs on power costs as well. All of that is reasonable we understand. Though hot water heaters do not require a lot with regard to maintenance (and we are astounded, even though not shocked, by the amount of customers we come across who haven’t executed anything to their water heater), following are the responsibilities individuals must keep in mind with regards to routine maintenance.

How Long Should My Arlington TX Water Heater Last?

The common gas water heater lasts 8 to 10 years. There are numerous things which may have an affect on the all around life expectancy needless to say, however this is an effective standard. Almost certainly the greatest factor that can influence the long life of it is normally mineral deposits. A lot of of the steps in this article should go a long way in assisting to lower the accumulation of mineral deposits within the storage tank of the water heater.

Arlington Water Heater Repair PreventionHot Water Heater Repair Arlington TX

House owners, even people which usually do not feel extremely handy, are capable of doing lots of water heater care by themselves. Although usually, water heaters are safe and sound, it is crucial to bear in mind that they actually do work from electric power and/or gas, for that reason correct safety techniques have to be taken. Be sure to implement all these measures as an instructional tutorial, for we’d much rather discuss all these together with you directly. The electrical power to the water heater requires to be switched off ahead of carrying out any routine maintenance. Ones breaker box ought to have a preferably labeled switch to point out which breaker is the heater’s. With a gas heater, move the gas cutoff counterclockwise to shut off the gas to the heater.

The portion of the heater that aids with avoiding rusting inside of the water storage tank are the anode rods, or additionally named sacrificial anode rods. Nearly all are made from aluminum or magnesium around a steel wire. In time the external covering of the rods will erode and they really should be replaced when the steel wire is noticeable. They typically last around 5 years, though that may be reduced if ones water is soft. In time, it is better and less costly to have the anode rods changed, so that one can acquire an extended life from the water heater storage tank. The rods should really be looked at on an annual basis.

The follow video does a very good job of demonstrating the method needed with replacing the anode rods:

Not every water heater has dip tubes. They must be reviewed for deterioration every 6 months. To evaluate it, take it out and evaluate its length to the height of the water heater. It needs to be around 6″ to 8″ shorter compared to the tank. Whenever it’s smaller than that, or simply displays clues of breakage or falling apart, it’ll need to get changed.

The big and small flush. Once more, mineral deposits are the major reason of water heater malfunctions. Based on the level of quality of water in ones residence will establish exactly how rapidly sediment will establish inside of the storage tank. This sediment can solidify in time, creating unusual popping sounds from the storage tank, decrease the effectiveness of the water heater, and perhaps clog up the drain valve. If possible, every 6 months, but at the least every year, empty 1 or 2 gallons of water from the drain valve in the bottom of the hot water heater in a pail or by a hose in a container outside the house. Look to determine the amount of sediment is within the pail after the water settles. If it seems pretty clear, that great! When these kinds of small flushes are undertaken 2 times yearly, one may well not need to complete a big flush as frequently. If the water seems to be very dirty, a full flush should really be conducted. It is likewise a very good occasion to ensure the bottom drain valve of the storage tank is functioning properly and not leaking. Most are ordinarily composed of plastic and with time when they aren’t opened up, they may get stuck or not close up firmly, so opening and closing them in the course of the small flush test is very good.

There can be unique measures one could take while flushing to deal with any specific water smells which could happen when hot water comes from faucets within the residence also.

This video illustrates exactly how and advantages for a water heater flush:

Regarding holiday or temporary houses, one will need to empty the storage tank of all its water in order to avoid any kind of flooding when the dwelling is not being occupied. Naturally, make certain to fill it up while the residence is to be resided in once again.

Water pipe inspection. Look to ensure all water piping have no leaks or are impaired at all. This should be straightforward to see when there are any leaks with any piece of the water plumbing or storage tank for it will have water below and/or near the device. Leaking water may cause water damage to areas of ones house, so ensure all seems dry, primarily if the heater is within the property and not in a garage.Arlington Water Heater Repair

T&P valve assessment. The T&P valve, also known as the temperature and pressure relief valve, must be looked at annually. The goal of the T&P valve would be to preserve the water heater storage tank from extra pressure, and exploding, not to frighten everyone. The owners handbook must be looked over to be sure the correct techniques are used but listed here are the fundamental actions. A little water may come out of the valve and it will probably be really hot so use caution. Raise the handle and let go of it. Have a container available to catch any extra water that can come out. When the handle is lifted, the noise of pressure getting discharged will be noticed. The handle will need to snap back into position. In the event that it won’t give it a try once more. In case it will not go back again into position following a number of attempts, it is going to have to be changed. The valve may possibly drip a little water after doing that for a short period of time. If it fails to discontinue dripping after a couple of hours contact us.

There does exist a lot of discussion on what the ideal temperature setting really should be. The manufacturer pre-programmed setting is in most cases 140 degrees, which is indeed warmer than almost all people definitely will ever have to have. 120 degrees is the common temperature and a number of people also go as far as 100 degrees. We’ll be publishing much more on this subject in the near future, but we highly recommend not going over 120 degrees.

Just For Gas Water HeatersWater Heater Repair Arlington TX

The gas venting system requires being checked out each 3 months. Examine to guarantee all fittings are tight and for obstructions and harm to the vent pipes along with making certain they’re absolutely free of rust and deterioration .. Gas fired hot water heaters vent fumes to the outdoors of the house. If these fumes flow within the dwelling it might be deadly and a fire threat. Ensure everything combustible or corrosive is faraway from the exhaust ventilation to alleviate problems with fires. Change all loose, broken or corroded areas of vent pipes.

Examine the pilot light to do a visual test of the way it is working. The pilot light is the element that ignites the gas burner that will heat the water. A clean burning and correctly adjusted pilot light is necessary for your water heater to function at peak efficiency. The color of the flame of the pilot light ought to be blue with natural gas heaters or blue/green with just a bit of yellow at the tip with propane heaters. A short flame, a yellow flame, or a flame with a divided flame at the top implies that a modification is necessary.

Just For Electric Water Heaters

Utilizing insulation wraps or covers around the storage tank can certainly help maintain a regular temperature inside of the storage tank without the need for as much electrical power. Additionally, with the heater not needing to perform as often will increase the life span of the heating element as it will not be put to use as much. Every 3 months roughly, look at to verify the insulation wrap is attached nicely and hasn’t fallen or shifted on the water storage tank.

Routine evaluation of the heating element is crucial and definitely will help decrease the need for an unexpected repair. We aren’t going to get into the specifics for a total assessment right here, however one will require a voltage/OHM meter to assure there does exist a closed electrical circuit. Heating elements will need updating from time to time.

Continue to keep the place close to ones water heater thoroughly clean of dirt. Notably if the water heater is positioned in the garage area, be certain to keep the vicinity swept. The cleaner the heater is, the considerably better it is going to work without having the necessity of a water heater repair.

Replace Old Water Heaters With Energy Efficient Ones

Today, nearly all water heaters made have a very fine volume of energy efficiency. In April of 2015, new codes were started in the United States on water heaters. Clearly, the better quality the heater, the longer the life one could possibly get from the device while using ideal servicing over time. Don’t wait to phone Hot Water Heater Repair Arlington TX to talk about water heater maintenance or even to help answer any concerns on deciding on the most proper replacement water heater for ones house or workplace. Brand, model, and size should all be considered throughout the selection process and not simply implement the “bigger the better” saying. With regard to storage tank water heaters, one doesn’t need to be always maintaining a surplus quantity of heated up water that won’t be used.

Water Heater Troubleshooting Suggestions

Hot water heaters are one of a property’s most diligently operating devices. Day or evening, it’s creating completely heated water at any time when you would like it. When it unexpectedly is no longer working correctly, many of us have the tendency to worry.

Luckily a nonfunctioning water heater does not constantly indicate a pricey repair work. Prior to making an emergency call to Water Heater Repair Arlington TX, we recommend examining the trouble yourself first.

Arlington TX Water Heater Repair Troubleshooting

Check the Pilot Light

For a gas water heater, eliminate the small panel on the bottom of the appliance and look to notice if the pilot light is ignited.
Spark it with a match or lighter to re-ignite it. If it remains lit, the water heater need to kick-in and begin operating appropriately.
If the pilot burner on the water heater does not remain ignited, you might should change the thermocouple or have the burner cleaned.

Replace the ThermocoupleWater Heater Repair Arlington

It seems like a really specialized title, however it’s in fact a basic gadget that you can change on your water heater.

Check the owner’s guide. It must have directions for the best ways to get rid of and change the thermocouple.
Switch off the gas prior to taking out anything at all from the water heater.
Using the guidelines in your individual’s handbook, eliminate the thermocouple by separating it from both sides of the aviator line.
Change the thermocouple on the water heater with a brand-new one that is cut to length.
Turn on the gas and check for leakages, then re-light the pilot light.

Hit the Reset Button

If you have an electric water heater, find the reset button and push it till you notice a click.
If you do not notice a click, or it falls short to reboot the water heater, reset the breaker.
If a breaker reset does not suffice, you could require to change the thermostat.

Change the Thermostat

Shut down the power to the water heater, and turn off the breaker it is linked to. You do not wish to electrocute yourself!
Use the owner’s guide to find the thermostat wires, then separate them.
Eliminate the thermostat and have it checked by a home appliance dealership. If it is damaged, change it.

Change the Heating Element

With the power still turned off, get rid of the gain access to panel on the water heater.
Loosen the terminal screws and pull the wires far from the heating element.
Get rid of each part of the element and have them checked by a device repair shop. If they are defective, change them.

Your water heater ought to be working in no time. If these actions fall short to repair your hot water heater, or if you do not feel relaxed doing them by yourself, call Hot Water Heater Repair Arlington TX.

Water Heater Repair Video Overview

We really enjoy the things we do here at Water Heater Repair Arlington TX and look forward to serving as many of our Arlington neighborhood friends as possible. We will continue to include suggestions on water heater maintenance right here in this blog too.

We desire to share our brand new company summary video to you below.

We are additionally readily available to support you with all other kinds of plumbing repair you might require carried out. Whether it is a leaking faucet, drain cleaning, toilet repair, or leak detection. We have witnessed nearly any sort of emergency plumbing and water heater repair scenario you can picture and look forward to utilizing our well crafted troubleshooting knowledge!

If you are believing it is becoming near requiring a water heater replacement contact us also, for we will do all we can to help support you in that circumstance.